banner
Scrap Cable Granulator Separator Machine
  • Scrap Cable Granulator Separator Machine
  • cable separator machine D15
  • copper wire separation machine D15
  • copper wire separator machine D15

Scrap Cable Granulator Separator Machine

1:Fit for separating copper wire and aluminum wire.
2:Capacity is about 100kg/h.
3:Add 2air filter on basic of BS-D10.
4:Feeding inlet is lower than normal machine.
5:Raw material inlet and copper outlet are separate, and more convenient to operate.

Machine Introduction:

Scrap cable granulator separator machine is dry type, mainly used for all kinds of waste copper wires, copper wires will be separated into tiny copper rice and PVC.

●This wire granulator machine can recycle electric wires whose diameter is below 25mm, including automobile electrical wire or car electric wire, motorcycle electric wire, computer case wire and communication cable, etc.

●Copper is separated from plastic, and copper separation rate is 99.9%.

●Copper granule can be sold directly or go to further refining. Through our copper recycling machine, copper can be refined into cathode copper above 99.9% purity.

●Plastic granules normally are PVC or rubber material, they can also be sold directly.

Machine Advantages:

BS-D15-1 cable recycling machine is our latest design which is on the basis of BS-D10 model, this model has following advantages:

1: Inlet lower than BS-D10;

2: Add 2 air filters;

3:Has dust collector bag;

4: Inlet and copper outlet are separate;

More ergonomic, when worker input material, it's easy and convenient to observe inlet situation.


Machine Technical Data:

BS-D15-1 parameters
Processing DiameterBelow 25mm
Machine Size2250*2000*2000mm
Machine Weight1000kg
Machine Voltage380V/220V or customized
Processing Capacity100KG/H
Motor Power23KW


Machine Working Process:

Through crushing, gravity separating, vibration screening, and pulse dust collecting, separation rate of copper and plastic will reach about 99.9%, you will get pure copper rice and plastic granulaues like below picture show.

dry granulator


Operating Steps:

1、Start 

Please confirm whole machine parts are in good condition, and connect electricity. 

Please clear up excess stock before getting machine started, no load for 5-10 minutes. 

No. on control panel is matched parts on machine with mark No. 

2、Infeed 

Please clear up iron from mixed cables, get crusher started, infeed according to crusher's capacity. 

3、Fine crushing 

Crushing and separating cables(5-10cm )come from Number 2 conveyor, if any abnormal noise, please stop and open crusher, 

Inspecting or changing screen, if any part run hot, please stop it and inspect. 

4、Vibrate and separate 

1)Scrap stuff after crushing, material will be delivered to separator via feeding fan. 

2)Copper from vibrator is complete copper, copper from feed opening needs second crushing.

Note: If problem in separating, terms of settlement: 

If see plastic in copper granules, please adjust wind power of the vibrator, bottom wind power adjust vibration frequency, wind power of dust absorption. 

1))If there still has plastic in copper, please check filter screen, please clean dust. 

2))If output is too low, please inspect. 

3))If copper granules output quantity is becoming less, please inspect vibrator, please brush off copper granules on the vibrator's screen. 

4)) Before getting vibrator started or turned off, please make sure the vibrator's frequency return to zero, otherwise the next time vibrator starting will have riddler damaged. 


Blade Adjusting & Replacing: 

Fixed Blades 

1. Front Fixed Blades:

Loosen fixed blades screws with socket wrench, and then adjust screws with open-ended wrench for adjusting spacing between fixed blades and rotating blades. If screws for fixed blades are removed, you can remove rotating blades for sharpening or replacing. 

2. Back Fixed Blades: 

Loosen fixed blades screws with socket wrench, and then adjust screws with open-ended wrench for adjusting spacing between fixed blades and rotating blades. If screws for fixed blades are removed, you can remove rotating blades for sharpening or replacing. 

Rotating Blades 

Loosen screws properly for rotating blades with socket wrench, adjust blade spacing and tighten screws after adjusting completed. 

If screws for fixed blades are removed, you can remove rotating blades for sharpening or replacing. 


Machine Easy Consume Parts:

Before you order, please note that:

BSGH can add special parts with scrap cable granulator separator machine according to your needs,

1: High Strength Magnetic separator: Separate and remove the iron.

2: Electrostatic separator: Improve separation rate.

3: Dual shaft shredder: Pre-shred and expand the capacity.


Machine Different View Pictures:

cable separator machine

Machine Right


cable wire separator machine

Machine Front


used cable wire separator machine

Machine Left


BSGH EQUIPMENT Aftersale Service:

1: Overseas technical support available.

2: All day long 24-hour service, call me: 008613772508206.

Hot Tags: scrap cable granulator separator machine, manufacturers, suppliers, factory, wholesale, buy, customized, cheap, distributor, dealer, low price, for sale, best quality

Categories

Hot Sale

  • QR Code

  • QR Code